Différences
Ci-dessous, les différences entre deux révisions de la page.
Les deux révisions précédentes Révision précédente Prochaine révision | Révision précédente | ||
2015:abuledu_client_15.08:analyse_configuration_wifi [2017/04/02 16:29] erics |
2015:abuledu_client_15.08:analyse_configuration_wifi [2017/04/04 11:31] francois |
||
---|---|---|---|
Ligne 31: | Ligne 31: | ||
Octets reçus:0 (0.0 B) Octets transmis:0 (0.0 B) | Octets reçus:0 (0.0 B) Octets transmis:0 (0.0 B) | ||
</ | </ | ||
- | _________________ | + | |
- | root@poste-10hp:/ | + | Parfois le bouton wifi (une touche du clavier ou un commutateur logiciel) interdit l' |
+ | |||
+ | < | ||
0: phy0: Wireless LAN | 0: phy0: Wireless LAN | ||
Soft blocked: no | Soft blocked: no | ||
Ligne 45: | Ligne 47: | ||
Soft blocked: no | Soft blocked: no | ||
Hard blocked: no | Hard blocked: no | ||
+ | </ | ||
+ | En cas de blocage (yes), il est possible d' | ||
+ | '' | ||
- | _____________________________ | + | Ensuite on peut lancer manuellement la carte wifi pour essayer d' |
+ | On commence par stopper la carte réseau | ||
- | tail -f / | + | < |
ifdown wlan0 | ifdown wlan0 | ||
+ | ifconfig wlan0 down | ||
+ | < | ||
- | root@poste-10hp:/ | + | Puis on la lance manuellement |
- | eth0 Link encap: | + | |
- | inet adr: | + | |
- | adr inet6: fe80:: | + | |
- | UP BROADCAST RUNNING MULTICAST | + | |
- | Packets reçus:926 erreurs:0 :0 overruns:0 frame:0 | + | |
- | TX packets:819 errors:0 dropped:0 overruns:0 carrier:0 | + | |
- | collisions: | + | |
- | Octets reçus: | + | |
- | lo Link encap: | + | < |
- | inet adr: | + | ifconfig wlan0 up |
- | adr inet6: ::1/128 Scope: | + | </code> |
- | UP LOOPBACK RUNNING | + | |
- | Packets reçus:0 erreurs:0 :0 overruns:0 frame:0 | + | |
- | TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 | + | |
- | collisions: | + | |
- | Octets reçus:0 (0.0 B) Octets transmis:0 (0.0 B) | + | |
- | root@servecole ~ ☠ tail -f / | + | On lui demande d' |
- | ifup wlan0 sur le client | + | <code> |
- | + | ||
- | pas de requetes DHCP qui arrivent sur le serveur -> direction le point d' | + | |
- | + | ||
- | _________________________ | + | |
- | + | ||
- | ifconfig wlan0 up | + | |
iwlist wlan0 scanning | iwlist wlan0 scanning | ||
Ligne 122: | Ligne 110: | ||
.../... | .../... | ||
- | + | </ | |
- | ______________________ | + | |
Création d'une configuration WPA pour lancement manuel: | Création d'une configuration WPA pour lancement manuel: | ||
+ | < | ||
wpa_passphrase ABULEDU > / | wpa_passphrase ABULEDU > / | ||
(saisir le mot de passe) | (saisir le mot de passe) | ||
+ | </ | ||
- | ifconfig wlan0 down | + | et on lance enfin le client wpa à la main en mode debug: |
- | ifconfig wlan0 up | + | |
- | iwlist wlan0 scanning | + | |
+ | < | ||
wpa_supplicant -Dwext -iwlan0 -c/ | wpa_supplicant -Dwext -iwlan0 -c/ | ||
+ | </ | ||
+ | |||
+ | qui affiche entre autre des informations intéressantes: | ||
+ | < | ||
.../... | .../... | ||
wlan0: Radio work ' | wlan0: Radio work ' | ||
Ligne 150: | Ligne 142: | ||
wlan0: Setting scan request: 5.000000 sec | wlan0: Setting scan request: 5.000000 sec | ||
.../... | .../... | ||
+ | </ | ||
+ | |||
+ | Dans notre cas l' | ||
- | SSID Mismatch -> hé oui il faut ABULEDU en majuscule |